VAN WATERS & ROGERS INC -- MAXFORCE ROACH KILLER GEL  -- 6840-00N059562
<pre>=====================  Product Identification  =====================

Product ID:MAXFORCE ROACH KILLER GEL
MSDS Date:11/01/1992
FSC:6840
NIIN:00N059562
=== Responsible Party ===
Company Name:VAN WATERS & ROGERS INC
Address:6100 CARILLON POINT
City:KIRKLAND
State:WA
ZIP:98033
Country:US
Info Phone Num:206-889-3400
Emergency Phone Num:800-424-9300(CHEMTREC)
CAGE:DO735
=== Contractor Identification ===
Company Name:VAN WATERS & ROGERS SUBSIDIARY OF UNIVAR
Address:6100 CARILLON POINT
City:KIRKLAND
State:WA
ZIP:98033
Country:US
Phone:425-889-3400
CAGE:DO735
Company Name:VOPAK USA INC
Address:6100 CARILLON POINT
Box:City:KIRKLAND
State:WA
ZIP:98033-7357
Country:US
Phone:425-889-3400/425-889-3617
CAGE:0STM5

=============  Composition/Information on Ingredients  =============

Ingred Name:2(1H)-PYRIMIDINONE, TETRAHYDRO-5,5-DIMETHYL-, (3-
    (4-(TRIFLUOROMETHYL)PHENYL)-1-(2-(4- (TRIFLUOROMETHYL)PHENYL)(ING
    2)
CAS:67585-29-4
RTECS #:UW7583000
Fraction by Wt: 2.0%
Other REC Limits:1.4 MG/M3 (TWA)(MFR)
OSHA PEL:N/K 
ACGIH TLV:N/K 

Ingred Name:ING 1:ETHENYL)-2-PROPENYLIDENE) HYDRAZONE; (HYDRAMETHYLNON)
RTECS #:9999999ZZ

=====================  Hazards Identification  =====================

LD50 LC50 Mixture:NONE SPECIFIED BY MANUFACTURER.
Routes of Entry: Inhalation:NO	Skin:NO  Ingestion:NO
Reports of Carcinogenicity:NTP:NO    IARC:NO	OSHA:NO
Health Hazards Acute and Chronic:MAXFORCE BAIT GEL IS MINIMALLY
    IRRITATING TO THE EYES AND SKIN. IT IS NOT ACUTELY TOXIC UPON ORAL
    OR DERMAL EXPOSURE. PROLONGED OR REPEATED EXPOSURE TO LARGE AMOUNTS
    OF THE ACTIVE INGREDIENT - HYDRAME THYLNON - MAY CAUSE TESTICULAR
    ATROPHY AND REPRODUCTIVE EFFECTS. HOWEVER, THESE EFFECTS ARE HIGHLY
    (EFTS OF OVEREXP)
Explanation of Carcinogenicity:NOT RELEVANT
Effects of Overexposure:HLTH HAZS:UNLIKELY TO OCCUR FROM USE OF THE
    BAIT GEL. FOLLOW THE PRECAUTIONS OUTLINED IN CONTROL MEASURES AND
    STORAGE AND HANDLING.
Medical Cond Aggravated by Exposure:NONE SPECIFIED BY MANUFACTURER.

=======================  First Aid Measures  =======================

First Aid:INHALATION:REMOVE TO FRESH AIR. SUPPORT BREATHING (GIVE
    O*2/ARTF RESP) . EYES:IMMEDIATELY FLUSH W/POTABLE WATER FOR A
    MINIMUM OF 15 MINUTES, SEEK ASSISTANCE FROM MD . SKIN:FLUSH
    W/COPIOUS  AMOUNTS OF WATER. CALL MD . INGESTION:DRINK 2 GLASSES OF
    WATER & INDUCE VOMIT BY TOUCHING BACK OF THROAT W/FINGER. DO NOT
    INDUCE VOMIT/GIVE ANYTHING BY MOUTH TO AN UNCON PERSON. GET MED
    ATTN.

=====================  Fire Fighting Measures  =====================

Flash Point:NOT FLAMMABLE
Extinguishing Media:MEDIA SUITABLE FOR SURROUNDING FIRE .
Fire Fighting Procedures:WEAR NIOSH/MSHA APPROVED SCBA & FULL
    PROTECTIVE EQUIPMENT .
Unusual Fire/Explosion Hazard:NOT FLAMMABLE OR EXPLOSIVE.

==================  Accidental Release Measures  ==================

Spill Release Procedures:NON-HAZARDOUS WASTE. PLACE IN A CONTAINER FOR
    DISPOSAL.
Neutralizing Agent:NONE SPECIFIED BY MANUFACTURER.

======================	Handling and Storage  ======================

Handling and Storage Precautions:AVOID SKIN AND EYE CONTACT.
    INSECTICIDE, NON-TOXIC, SOLID-NOT RESTRICTED.
Other Precautions:IMMEDIATELY REMOVE CONTAMINATED CLOTHING SHOULD
    CONTACT OCCUR.

=============  Exposure Controls/Personal Protection  =============

Respiratory Protection:USE NIOSH/MSHA APPROVED RESPIRATOR APPROPRIATE
    FOR EXPOSURE OF CONCERN .
Ventilation:USE GENERAL VENTILATION TO MINIMIZE EXPOSURE.
Protective Gloves:WEAR IMPERVIOUS GLOVES.
Eye Protection:ANSI APPROVED CHEM WORKERS GOGGS .
Other Protective Equipment:WHEN HANDLING LARGE AMOUNTS OF PRODUCT WEAR
    IMPERVIOUS APRON.
Work Hygienic Practices:LAUNDER CLOTHING BEFORE RE-USE.
Supplemental Safety and Health
NONE SPECIFIED BY MANUFACTURER.

==================  Physical/Chemical Properties  ==================

Spec Gravity:1.05-1.15
Appearance and Odor:THICK YELLOW GEL

=================  Stability and Reactivity Data  =================

Stability Indicator/Materials to Avoid:YES
NONE SPECIFIED BY MANUFACTURER.
Stability Condition to Avoid:PRODUCT WILL STAIN POROUS SURFACES.
Hazardous Decomposition Products:NONE SPECIFIED BY MANUFACTURER.

====================  Disposal Considerations  ====================

Waste Disposal Methods:DISPOSE IN ACCORDANCE WITH LOCAL, STATE AND
    FEDERAL REGULATIONS.

 Disclaimer (provided with this information by the compiling agencies):
 This information is formulated for use by elements of the Department
 of Defense.  The United States of America in no manner whatsoever,
 expressly or implied, warrants this information to be accurate and
 disclaims all liability for its use.  Any person utilizing this
 document should seek competent professional advice to verify and
 assume responsibility for the suitability of this information to their
 particular situation.